The 'db' Jeep Chronicles
After
Current
Note: Previous weeks are listed here below the To Do List.
To-Do List
- Remove old body
- Remove old fuel system
- Tank
- Lines
- Remove brake lines
- Remove engine
- Clean frame
- Wash frame
- Replace front U joints
- Repair frame
- Body Mounts
- Left & Right Rear Frame Members
- Gas Tank Cross Member
- Secondary Cross Member
- Driver Side frame by transmission
- Rider Side front by front end
- Sandblast frame
- Rustproof frame
- Reinstall front end axel and hardware
- Reinstall rear axel
- Reinstall front and rear bumpers
- New brake lines
- New gas tank
- New fuel lines
- Reinstall engine
- Body
- Fix body dents
- Paint body
- Install body
- Install Fenders
- Install Grill
- Install Windshield
- Install Tailgate
- Interior
- Break/clutch pedals
- Dashboard
- Steering wheel
- Seats
- Center console
- Rollbar
- Canvas Top
- Electrical system
- Repair Wreck Damage
- Straighten Frame
- Replace Leaf Springs
- Replace front shocks
- Straighten tie rod
- Straighten & Paint Front Fender
- Replace side marker light
- Get Comprehensive Insurance Coverage
- Winter 2004 Upgrade
- Two Barrel Carb
- Herculiner on floor
- Paint Roll Bar
- Replace starter
- Replace front u-joints
- Reorient air compressor
- Winter 2005 Upgrade
- Two new axels w/ 3.4 gears
- Spring 2006 Upgrade
- New (old) engine!
- Spring 2008 Upgrade
- Roll Cage!
02/01/2001 - 02/28/2001
03/01/2001 - 03/31/2001
04/01/2001 - 04/30/2001
05/01/2001 - 05/31/2001
06/01/2001 - 06/30/2001
07/01/2001 - 07/31/2001
08/01/2001 - 08/31/2001
09/01/2001 - 09/30/2001
12/01/2001 - 12/31/2001
02/01/2002 - 02/28/2002
05/01/2002 - 05/31/2002
06/01/2002 - 06/30/2002
07/01/2002 - 07/31/2002
08/01/2002 - 08/31/2002
09/01/2002 - 09/30/2002
11/01/2002 - 11/30/2002
01/01/2003 - 01/31/2003
02/01/2003 - 02/28/2003
03/01/2003 - 03/31/2003
04/01/2003 - 04/30/2003
05/01/2003 - 05/31/2003
03/01/2004 - 03/31/2004
Welding - Something every Jeep rebuilder should know how to do. And I don't. So, time to do what every web savvy guy would do. Start searching the net for info. I looked into taking a class at the local vocational school but they want $450 for a 6 week class! Outch. Think I'm just going to buy my cousin’s husband some lunch and have him show me the basics. Anyone know of a good way to learn welding that doesn't cost an arm and a leg? Let me know.
[3 comments]
On Board Air - That's the next upgrade in the works. I've been discussing it with a friend and I think I'm going to find an old York a/c compressor and mount it under the hood. Then wire up a switch to turn the magnetic clutch on and off and finally just mount a pressure relief and quick disconnect fitting to the output. I've seen this work great for inflating tires and simple things like that. No need for a tank, at least not for now. I'll keep you posted on the progress. I've ordered the pressure relief valve and should see it in a few days. Now to find an old York somewhere.
[Add comments?]
Tue, Feb 23, 2001
©2001-2003 Saturday!, Dan Berlyoung